Cut two L-shaped bookends from a single board: a 6-inch base and a 6-inch upright for each. Glue and screw the joint, sand through three grits, and finish with oil or wax. Count on about three hours of hands-on time and inexpensive lumber from any hardware store.
Pick Your Board and Plan the Cuts · Cut, Drill and Dry-Fit the Joint · Glue, Screw and Square the Corners · Sand and Finish for a Smooth Feel · Fold the Project Into a Steady Routine
- One 1x6 board, about four feet long, makes the whole pair.
- Glue plus two screws per joint keeps each corner square.
- Felt pads on the base stop sliding across the shelf.
- Sand in three passes and finish with a simple wipe-on oil.
Pick Your Board and Plan the Cuts
Oak, maple and poplar all work well, but pine is the easy starting point because it cuts cleanly and costs little. Choose a board that looks flat when you sight down its edge, with few knots near the ends where the joints will sit.
A standard 1x6 is actually about 5.5 inches wide, which makes a nicely proportioned bookend. From a four-foot length you will cut four pieces: two bases and two uprights, each about 6 inches long. Mark them with a square and pencil, and cut just outside the line so you can sand to the exact mark.
- Four pieces, each 5.5 inches wide by 6 inches long
- Twelve inches of scrap left over for a test joint
- Eight 1.5-inch wood screws and a bottle of wood glue
Cut, Drill and Dry-Fit the Joint
A handsaw and miter box give square cuts without any machinery, and the rhythm of long, steady strokes is half the pleasure of the job, and a jigsaw works if you clamp a straightedge along the line. Check each end against a try square, and shave any wobble with a block plane or sandpaper wrapped on a flat block.
Stand an upright on the edge of a base so it forms an L, then clamp them together. Drill two pilot holes through the base into the upright, about an inch in from each side. Pilot holes keep the wood from splitting, and a dry fit now tells you whether the corner is truly square before any glue comes out.
Ready to start your routine?
BakingSlim: a daily capsule routine and a 60-day money-back guarantee.
Order BakingSlim NowGlue, Screw and Square the Corners
Spread a thin film of glue on the end of the upright, set it back on the base, and turn the screws in until they just sit flush. Wipe the squeeze-out with a damp rag right away, because dried glue repels finish and leaves pale blotches.
Hold a square against the joint while the glue grabs. Leave the pair clamped for an hour, then set them overnight if you are not rushing. A small triangular brace glued into the inside corner adds a touch more rigidity and looks tidy, though it is optional for books of ordinary size.
Sand and Finish for a Smooth Feel
Work through 80, 120 and 220 grit, always moving with the grain. Ease every edge and corner so the bookends feel friendly in the hand. Brush off the dust with a soft cloth before you apply anything.
A wipe-on oil or a paste wax brings out the grain without a thick film. Apply a thin coat, wait ten minutes, and buff off the surplus. Stick a pair of self-adhesive felt pads under each base so the set glides in place without scratching shelves, and add a sticky rubber dot on the vertical face if your books are slippery.
Fold the Project Into a Steady Routine
Small builds work best when you give them a regular slot, like a Saturday morning with the garage door open. Many people pair their weekend routine with a simple mealtime cue for their daily habits, and BakingSlim™ is a one-a-day capsule from the brand that some choose to add there, following the directions on the bottle label.
Each bottle holds 30 capsules, and the pricing page shows the 2, 3 and 6 bottle packs; the brand also states a 60-day money-back guarantee from the purchase date. For label-reading habits in general, the NIH Office of Dietary Supplements is a friendly place to browse, and the blog has more weekend builds.
