Skip to content
Packs of 2, 3 or 6 bottles60-day money-back guaranteeSecure checkout
BakingSlim™
Home/Blog/How to Make a Copper Pipe Wind Chime
Lifestyle

How to Make a Copper Pipe Wind Chime

By BakingSlim Editorial TeamPublished October 11, 2026Updated November 17, 20264 min read
Quick answer

Cut five lengths of half-inch copper pipe, drill them near the top, and hang them from a wooden disk with braided line. Add a center clapper and a wind sail. Longer pipes ring lower, shorter ones higher, so a staggered set gives a pleasant, gentle sound outside.

Key takeaways
  • Half-inch copper pipe is easy to cut and rings clearly.
  • Hang each tube about a quarter of the way down its length.
  • A wooden disk and a small clapper complete the build.
  • Staggered lengths make a soft, musical sound in a breeze.

Gather Pipe, Line and a Hanging Disk

Plumbing aisles hold nearly everything you need. Pick up a three-foot stick of half-inch copper pipe, a spool of braided nylon or waxed cord, small eye screws, and a three-inch wooden disk for the top. A smaller disk, about two inches, will serve as the clapper in the middle.

Round out the kit with a hacksaw or tubing cutter, a file, a drill with a 1/8-inch bit, a ruler and a marker. A tubing cutter gives the cleanest edge, but a hacksaw works if you take your time and keep the cut square.

  • Half-inch copper pipe, about three feet
  • Wooden disk for the top and a smaller one for the clapper
  • Braided line, eye screws and a split ring for hanging

Cut Lengths That Sound Good Together

Pitch follows length: the longer the tube, the lower the tone. A pleasing starter set is 10, 11, 12.5, 14 and 16 inches. Spacing the lengths unevenly keeps the chime from sounding like a single repeated tone.

Mark each length, then cut slowly and rotate the pipe as you go. Smooth the inside and outside edges with a file so no burrs catch the line. Wipe every piece with a cloth so the metal has a bright, even surface before you hang it. Lay the cut tubes on a towel in order from shortest to longest, which makes it easy to picture the finished chime and catch a length that looks out of place. Rub a little fine steel wool over any fingerprints; copper shows every touch until it ages evenly.

Ready to start your routine?

BakingSlim: a daily capsule routine and a 60-day money-back guarantee.

Order BakingSlim Now

Drill the Hanging Holes in the Right Spot

Each tube should hang from a point about 22 percent of the way down from the top, which is where it vibrates most freely. On a 12-inch pipe, that is roughly 2.6 inches from the end. Mark that point, then drill straight through both sides of the pipe.

Clamp the pipe in a vise wrapped in a rag so the metal is not marred, and start the drill with a light touch. Threading the line through both holes forms a neat loop, and a figure-eight knot at the top keeps it from sliding.

Assemble the Chime and Add the Sail

Drill five small holes around the wooden disk, evenly spaced, and tie each tube on with a loop of line at different lengths so the bottoms line up in a gentle staircase. Screw an eye into the center of the disk and hang the small clapper from it, so it rests at the height of the middle of the tubes.

Cut a sail from a thin wood scrap or a sturdy piece of copper sheet and hang it below the clapper. The sail catches the wind and pushes the clapper into the tubes. Hang the finished chime from a split ring on a porch hook, away from railings where it might clang.

Hang It, Tune It and Enjoy the Routine

Listen for a week and adjust. If the tone is dull, slide the hanging holes slightly higher or lower; if the tubes click against each other, add an inch of line to the clapper. Copper will darken over time to a handsome brown, or you can buff it bright with a soft cloth.

Wind chimes suit an unhurried morning, the kind where you step outside with a cup in hand and keep to a few tidy habits. Many people anchor those habits to a mealtime cue, and BakingSlim™ is a one-a-day capsule that some include, following the bottle label. See the BakingSlim pricing page for pack sizes and the blog for more projects. For general reference on how labels are written, try PubChem.

Related guides

FAQ

Quick answers

Half-inch copper pipe is the usual choice. It is thin enough to ring brightly, thick enough to resist denting, and easy to cut with basic tools. Three-quarter-inch pipe gives a deeper, fuller tone but needs longer pieces. Whatever width you pick, use the same size throughout the chime so the tones sit well together.

Yes. Copper slowly darkens and eventually develops a brown or greenish patina outdoors. Many makers love that aged look. If you prefer a bright shine, buff the tubes with a soft cloth now and then, or spray them with a clear outdoor sealer before you hang the chime. Either way, the tone stays the same.

Each bottle holds 30 capsules, printed on the label as 30 Capsules and Dietary Supplement. The brand states one capsule once daily, so one bottle is about 30 days. The 2, 3 and 6 bottle packs equal 60, 90 and 180 capsules. Prices and shipping appear on the brand's secure order page before you pay.
Ready when you are

Start your BakingSlim routine today

A daily capsule bottle, a full label printed on it and a 60-day money-back guarantee. Choose a 2-, 3- or 6-bottle pack on the secure order page.

Order BakingSlim NowBacked by a 60-day money-back guarantee · Secure checkout
Six bottles of BakingSlim daily capsules
BakingSlim™ capsules60-day money-back guarantee
Order Now